Seeding & Tillage

32' Connor Shea bar fitted with knife points and press wheels and 4 tonne Symplicity tow behind box with small seeds.

33 tyne scarifier has been extended to 41 tyne. Easily removed if required. Good solid machine last used with heavy leveling bar to mix and level ofter delving.

Shearer 27 tyne converted to 9 inch rows with knife points and set up for banding. Small seeds box and press wheels. Was great machine but now needs work. Spares included, press wheels tynes etc.

Colenam 15 section harrows. Still work but getting old

Home made roller. Truck tyres

40 1inch Atom Jet points with liquid tube pipe

done 2 seasons

Black and Red ConservaPak parts.

12x Tyne units including Tyne,Side plates,Seeding boot,Spring can and presswheel.

Has not done much work. High lift to load into trucks and PTO power pack so you don’t have to have a high hyd flow tractor to operate 

6x  Raycol heads  63mm inlet 11 x 32 mm  outlets (2nd hand) some with caps

2 x Raycol heads 63mm inlet 12 x 32 mm outlets (2nd hand) 

5 x Raycol heads 38mm inlet   5 x 35 mm outlets (new)

Shearer trash culti seed drill, 28 run over 4 rows, with 3 row finger harrows, double sprung tynes, restrictors for small seeds and lower sowing rates, sets of sowing and cultivating points included, always shedded and is in excellent condition. 

48x Flexible boots with 40mm closure and brackets. $95 + GST Each if seperated.

61x Sweep adaptors with wedge, some have shears installed. $17 + GST Each if seperated.

11 tynes, 430mm spacing, 550mm ripping depth, Hydraulic auto-reset tynes, Clay blades with inclusion plates and wings, 5m working width, 3m transport width, Hydraulic tandem spiked roller. Very good condition, selling due to going down a different pathway   

Manutec wheels. Will sell individually or mounting bars and brackets. 
Are mounted on a 44ft ST820 on 9 inch spacing. 

$132 inc GST individual press wheels 

$8800 inc GST with mounting brackets etc. 

open to offers 

Very good condition has small seed box. Hdy in and out.  Used this year.  Two remote at the back.  

12 m Bar 12 inch spacing with splitter Boot Single shoot have knock on points Agoint also have Acermate points available

All Packer Wheels bearing replaced and all new bushes

Nothing spared on the packers

A good strong average condition bar also TBH Case 2300 Bin with Rice Lug Tyres good Condition 2 Bin Easy too Calibrated Ready too go

Only selling due too going back to one Machine

Needs new bearings and drive chains 

11.00 tyres

Ex condition

Adjustable walking press wheel assembly's 

15" wheels

As new, 14 sets

Morris 7240 box & 52 foot bar

Working condition needs a tidy up 

Always shedded

New Holland 3030 28ft airseeder, 3350 cart, presswheels, new hydraulic hoses and rams 2023. Good, tidy condition. Some hoses could do with replacing. Always shedded, only outside to sell. No longer required

Property sold, must sell.

10.5” spacing. Modified tyne layout for improved trash clearance.

Individual pivot arm press wheels for controlled sowing depth, Manutec 100mm.

Suit double or single shoot. No air kit.

Agpoint knife points. All 8 hyd rams reconditioned.

Extra tynes included. $15,000 +GST

4x8 wheel,1x7wheel,2x6 wheels gang. Surplus to requirements as have upgraded seeding unit

2008 John Deere 1910 tow between 2 bin, 270 Bushel (9500L), Pre-Seasoned by Emmetts $17k spent, ground drive, variable rate.

Dual Shoot currently setup on 4 Primaries for Fertiliser and 4 for Seed. Smallaire Heat Exchanger.

4 Metering Rollers, Rear Facing and Seed Bin Camera. 4 metering rollers, plenty of spares.

Available now. Can provide John Deere 2630 screen to run seeder for $8,000 + GST.

S64 Model

24ft

Second owner 

Minor repairs needed

$33,000 Inc

6.32m John Deere Disc units mounted on Fusion bar. 32 Disc Openers. 

Simplicity TB2 7500lt with small seed box.

Able to sow alternate row for mixed species.

New discs and Guage wheels. Heaps of spares, closing wheel bushes, opener arm bushes etc. 

Ezee-on 3500 seeder bar in great condition 

* 35 foot 

* 8 inch spacings 

* Ag master presswheels 

* Gason hose kit set up for tow behind but can be changed to tow between 

*All Pins and brushes have been replaced less than two years ago 

*Presswheels have all been rebuilt. 

Always kept in the shed, very well maintained reciving regular services.

Various spare parts including primary sales boots and heavy duty springs happy to negotiate prices. 

Older machine but will not disapoint. 

$24,000 inc GST

Morris 3 Bin Box, tow behind, ground drive. Currently set up for 6 sections, can be made to 8 sections.

Grizzly 16 plate tandem disc plough

very good condition 

Cat 1/2 3pl